Gph Filter

Reverse osmosis

History

The process of osmosis through semipermeable membranes was first observed in 1748 by Jean Antoine Nollet. For the following 200 years, osmosis was only a phenomenon observed in the laboratory. In 1949 the University of California at Los Angeles (UCLA) first investigated desalination of seawater using semipermeable membranes. Researchers from both UCLA and the University of Florida successfully produced freshwater from seawater in the mid-1950s, but the flux was too low to be commercially viable. The future of RO is promising. By the end of 2001, about 15,200 desalination plants were in operation or in the planning stages worldwide.

Process

A semipermeable membrane coil used in desalinization.

Formally, reverse osmosis is the process of forcing a solvent from a region of high solute concentration through a semipermeable membrane to a region of low solute concentration by applying a pressure in excess of the osmotic pressure.

The membranes used for reverse osmosis have a dense barrier layer in the polymer matrix where most separation occurs. In most cases the membrane is designed to allow only water to pass through this dense layer while preventing the passage of solutes (such as salt ions). This process requires that a high pressure be exerted on the high concentration side of the membrane, usually 217 bar (30250 psi) for fresh and brackish water, and 4070 bar (6001000 psi) for seawater, which has around 24 bar (350 psi) natural osmotic pressure that must be overcome.

This process is best known for its use in desalination (removing the salt from sea water to get fresh water), but since the early 1970s it has also been used to purify fresh water for medical, industrial, and domestic applications.

Osmosis describes how solvent moves between two solutions separated by a semipermeable membrane to reduce concentration differences between the solutions. When two solutions with different concentrations of a solute are mixed, the total amount of solutes in the two solutions will be equally distributed in the total amount of solvent from the two solutions. Instead of mixing the two solutions together, they can be put in two compartments where they are separated from each other by a semipermeable membrane. The semipermeable membrane does not allow the solutes to move from one compartment to the other, but allows the solvent to move. Since equilibrium cannot be achieved by the movement of solutes from the compartment with high solute concentration to the one with low solute concentration, it is instead achieved by the movement of the solvent from areas of low solute concentration to areas of high solute concentration. When the solvent moves away from low concentration areas, it causes these areas to become more concentrated. On the other side, when the solvent moves into areas of high concentration, solute concentration will decrease. This process is termed osmosis. The tendency for solvent to flow through the membrane can be expressed as "osmotic pressure", since it is analogous to flow caused by a pressure differential. Osmosis is a great example of Diffusion.

In reverse osmosis, in a similar setup as that in osmosis, pressure is applied to the compartment with high concentration. In this case, there are two forces influencing the movement of water: the pressure caused by the difference in solute concentration between the two compartments (the osmotic pressure) and the externally applied pressure.

Applications

Drinking water purification

Around the world, household drinking water purification systems, including a reverse osmosis step, are commonly used for improving water for drinking and cooking.

Such systems typically include a number of steps:

a sediment filter to trap particles including rust and calcium carbonate

optionally a second sediment filter with smaller pores

an activated carbon filter to trap organic chemicals and chlorine, which will attack and degrade TFC reverse osmosis membranes

a reverse osmosis (RO) filter which is a thin film composite membrane (TFM or TFC)

optionally a second carbon filter to capture those chemicals not removed by the RO membrane

optionally an ultra-violet lamp for disinfecting any microbes that may escape filtering by the reverse osmosis membrane

In some systems, the carbon pre-filter is omitted and cellulose triacetate membrane (CTA) is used. The CTA membrane is prone to rotting unless protected by chlorinated water, while the TFC membrane is prone to breaking down under the influence of chlorine. In CTA systems, a carbon post-filter is needed to remove chlorine from the final product water.

Portable reverse osmosis (RO) water processors are sold for personal water purification in various locations. To work effectively, the water feeding to these units should best be under some pressure (40 psi or greater is the norm). Portable RO water processors can be used by people who live in rural areas without clean water, far away from the city's water pipes. Rural people filter river or ocean water themselves, as the device is easy to use (Saline water may need special membranes). Some travelers on long boating trips, fishing, island camping, or in countries where the local water supply is polluted or substandard, use RO water processors coupled with one or more UV sterilizers. RO systems are also now extensively used by marine aquarium enthusiasts. In the production of bottled mineral water, the water passes through an RO water processor to remove pollutants and microorganisms. In European countries, though, such processing of Natural Mineral Water (as defined by a European Directive) is not allowed under European law. (In practice, a fraction of the living bacteria can and do pass through RO membranes through minor imperfections, or bypass the membrane entirely through tiny leaks in surrounding seals. Thus, complete RO systems may include additional water treatment stages that use ultraviolet light or ozone to prevent microbiological contamination.)

Membrane pore sizes can vary from .1 to 5,000 nanometers (nm) depending on filter type. "Particle filtration" removes particles of 1,000 nm or larger. Microfiltration removes particles of 50 nm or larger. "Ultrafiltration" removes particles of roughly 3 nm or larger. "Nanofiltration" removes particles of 1 nm or larger. Reverse osmosis is in the final category of membrane filtration, "Hyperfiltration", and removes particles larger than .1 nm.

In the United States military, R.O.W.P.U.'s (Reverse Osmosis Water Purification Unit, pronounced "roh-poo") are used on the battlefield and in training. They come ranging from 1500 GPD (gallons per day) to 150,000 GPD and bigger depending on the need. The most common of these are the 600 GPH (gallons per hour) and the 3,000 GPH. Both are able to purify salt water and water contaminated with N.B.C. (Nuclear/Biological/Chemical) agents from the water. During a normal 24 hour period, one unit can produce anywhere from 12,000 to 60,000 gallons of water, with a required 4 hour maintenance window to check systems, pumps, R.O. elements and the engine generator. A single ROWPU can sustain a force of a battalion size element or roughly 1,000 to 6,000 soldiers.

31st Marine Expeditionary Unit (MEU) Service Support Group 31

Water and wastewater purification

Rain water collected from storm drains is purified with reverse osmosis water processors and used for landscape irrigation and industrial cooling in Los Angeles and other cities, as a solution to the problem of water shortages.

In industry, reverse osmosis removes minerals from boiler water at power plants. The water is boiled and condensed repeatedly. It must be as pure as possible so that it does not leave deposits on the machinery or cause corrosion. It is also used to clean effluent and brackish groundwater.

The process of reverse osmosis can be used for the production of deionized water.

In 2002, Singapore announced that a process named NEWater would be a significant part of its future water plans. It involves using reverse osmosis to treat domestic wastewater before discharging the NEWater back into the reservoirs.

Dialysis

Reverse osmosis is similar to the technique used in dialysis, which is used by people with kidney failure. The kidneys filter the blood, removing waste products (e.g. urea) and water, which is then excreted as urine. A dialysis machine mimics the function of the kidneys. The blood passes from the body via a catheter to the dialysis machine, across a filter.

Food Industry

In addition to desalination, reverse osmosis is a more economical operation for concentrating food liquids (such as fruit juices) than conventional heat-treatment processes. Research has been done on concentration of orange juice and tomato juice. Its advantages include a low operating cost and the ability to avoid heat treatment processes, which makes it suitable for heat-sensitive substances like the protein and enzymes found in most food products.

Reverse osmosis is extensively used in the dairy industry for the production of whey protein powders and for the concentration of milk to reduce shipping costs. In whey applications, the whey (liquid remaining after cheese manufacture) is pre-concentrated with RO from 6% total solids to 10-20% total solids before UF (ultrafiltration) processing. The UF retentate can then be used to make various whey powders including WPI (whey protein isolate) used in bodybuilding formulations. Additionally, the UF permeate, which contains lactose, is concentrated by RO from 5% total solids to 1822% total solids to reduce crystallization and drying costs of the lactose powder.

Although use of the process was once frowned upon in the wine industry, it is now widely understood and used. An estimated 60 reverse osmosis machines were in use in Bordeaux, France in 2002. Known users include many of the elite classed growths (Kramer) such as Chteau Loville-Las Cases in Bordeaux.

Car Washing

Because of its lower mineral content, Reverse Osmosis water is often used in car washes during the final vehicle rinse to prevent water spotting on the vehicle. Reverse osmosis water displaces the mineral-heavy reclamation water (municipal water). Reverse Osmosis water also enables the car wash operators to reduce the demands on the vehicle drying equipment such as air blowers.

Maple Syrup Production

In 1946, some maple syrup producers started using reverse osmosis to remove water from sap before being further boiled down to syrup. The use of reverse osmosis allows approximately 54-42% of the water to be removed from the sap, reducing energy consumption and exposure of the syrup to high temperatures. Microbial contamination and degradation of the membranes has to be monitored.

Hydrogen production

For small scale production of hydrogen, reverse osmosis is sometimes used to prevent formation of minerals on the surface of electrodes and to remove organics from drinking water.

Reef aquariums

Typical RO/DI unit used for an aquarium

Many reef aquarium keepers use reverse osmosis systems for their artificial mixture of seawater. Ordinary tap water can often contain excessive chlorine, chloramines, copper, nitrogen, phosphates, silicates, or many other chemicals detrimental to the sensitive organisms in a reef environment. Contaminants such as nitrogen compounds and phosphates can lead to excessive, and unwanted, algae growth. An effective combination of both reverse osmosis and deionization (RO/DI) is the most popular among reef aquarium keepers and is preferred above other water purification processes due to the low cost of ownership and minimal running costs. (Where chlorine and chloramines are found in the water, carbon filtration is needed before the membrane, as the common residential membrane used by reef keepers does not cope with these compounds.)

Desalination

Areas that have either no or limited surface water or groundwater may choose to desalinate seawater or brackish water to obtain drinking water. Reverse osmosis is the most common method of desalination, although 85 percent of desalinated water is produced in multistage flash plants.

Large reverse osmosis and multistage flash desalination plants are used in the Middle East, especially Saudi Arabia. The energy requirements of the plants are large, but electricity can be produced relatively cheaply with the abundant oil reserves in the region. The desalination plants are often located adjacent to the power plants, which reduces energy losses in transmission and allows waste heat to be used in the desalination process of multistage flash plants, reducing the amount of energy needed to desalinate the water and providing cooling for the power plant.

Sea Water Reverse Osmosis (SWRO) is a reverse osmosis desalination membrane process that has been commercially used since the early 1970s. Its first practical use was demonstrated by Sidney Loeb and Srinivasa Sourirajan from UCLA in Coalinga, California. Because no heating or phase changes are needed, energy requirements are low in comparison to other processes of desalination, but are still much higher than those required for other forms of water supply (including reverse osmosis treatment of wastewater).[citation needed]

The Ashkelon seawater reverse osmosis (SWRO) desalination plant in Israel is the largest in the world. The project was developed as a BOT (Build-Operate-Transfer) by a consortium of three international companies: Veolia water, IDE Technologies and Elran.

The typical single pass SWRO system consists of the following components:

Intake

Pre-treatment

High-pressure pump

Membrane assembly

Remineralization and pH adjustment

Disinfection

Alarm/Control Panel

Pre-treatment

Pre-treatment is important when working with RO and nanofiltration (NF) membranes due to the nature of their spiral wound design. The material is engineered in such a fashion to allow only one way flow through the system. As such the spiral wound design doesn't allow for backpulsing with water or air agitation to scour its surface and remove solids. Since accumulated material cannot be removed from the membrane surface systems they are highly susceptible to fouling (loss of production capacity). Therefore, pretreatment is a necessity for any RO or NF system. Pretreatment in SWRO system has four major components:

Screening of solids: Solids within the water must be removed and the water treated to prevent fouling of the membranes by fine particle or biological growth, and reduce the risk of damage to high-pressure pump components.

Cartridge filtration - Generally string-wound polypropylene filters that remove between 1 - 5 micrometre sized particles.

Dosing of oxidizing biocides such as chlorine to kill bacteria followed by bisulfite dosing to deactivate the chlorine which can destroy a thin-film composite membrane. There are also biofouling inhibitors which do not kill bacteria but simply prevent them from growing slime on the membrane surface.

Prefiltration pH adjustment: If the pH, hardness and the alkalinity in the feedwater result in a scaling tendency when they are concentrated in the reject stream, acid is dosed to maintain carbonates in their soluble carbonic acid form.

CO3-2 + H3O+ = HCO3- + H2O

HCO3- + H3O+ = H2CO3 + H2O

Carbonic acid cannot combine with calcium to form calcium carbonate scale. Calcium Carbonate Scaling tendency is estimated using the Langelier Saturation Index. Adding too much sulfuric acid to control carbonate scales may result in calcium sulfate, barium sulfate or strontium sulfate scale formation on the RO membrane.

Prefiltration Antiscalants: Scale inhibitors (also known as antiscalants) prevent formation of all scales compared to acid which can only prevent formation of calcium carbonate and calcium phosphate scales. In addition to inhibiting carbonate and phosphate scales, antiscalants inhibit sulfate and fluoride scales, disperse colloids and metal oxides and specialty products exist to inhibit silica formation.

High pressure pump

The pump supplies the pressure needed to push water through the membrane, even as the membrane rejects the passage of salt through it. Typical pressures for brackish water range from 225 to 375 psi (15.5 to 26 bar, or 1.6 to 2.6 MPa). In the case of seawater, they range from 800 to 1,180 psi (55 to 81.5 bar or 6 to 8 MPa).

Membrane assembly

The layers of a membrane.

The membrane assembly consists of a pressure vessel with a membrane that allows feedwater to be pressed against it. The membrane must be strong enough to withstand whatever pressure is applied against it. RO membranes are made in a variety of configurations, with the two most common configurations being spiral-wound and a hollow-fiber.

Remineralisation and pH adjustment

The desalinated water is very corrosive and is "stabilized" to protect downstream pipelines and storages usually by adding lime or caustic to prevent corrosion of concrete or cement lined surfaces. Liming material is used in order to adjust pH at 6.8 to 8.1 to meet the potable water specifications, primarily for effective disinfection and for corrosion control.

Disinfection

Post-treatment consists of stabilizing the water and preparing for distribution. Desalination processes are very effective barriers to pathogenic organisms, however disinfection is used to ensure a "safe" water supply. Disinfection (sometimes called germicidal or bactericidal) is employed to sterilise any bacteria protozoa and virus that have bypassed the desalination process into the product water. Disinfection may be by means of ultraviolet radiation, using UV lamps directly on the product, or by chlorination or chloramination (chlorine and ammonia). In many countries either chlorination or chloramination is used to provide a "residual" disinfection agent in the water supply system to protect against infection of the water supply by contamination entering the system.

Disadvantages

Household reverse osmosis units use a lot of water because they have low back pressure. As a result, they recover only 5 to 15 percent of the water entering the system. The remainder is discharged as waste water. Because waste water carries with it the rejected contaminants, methods to recover this water are not practical for household systems. Waste water is typically connected to the house drains and will add to the load on the household septic system. An RO unit delivering 5 gallons of treated water per day may discharge 40 to 90 gallons of waste water per day to the septic system.

Large scale industrial/municipal systems have a production efficiency of closer to 48% because they can generate the high pressure needed for RO filtration.

New developments

Prefiltration of high fouling waters with another, larger-pore membrane with less hydraulic energy requirement, has been evaluated and sometimes used since the 1970s. However, this means the water passes through two membranes and is often repressurized, requiring more energy input in the system, increasing the cost.

Other recent development work has focused on integrating RO with electrodialysis in order to improve recovery of valuable deionized products or minimize concentrate volume requiring discharge or disposal.

See also

Electrodeionization

Hydrogen production

Microfiltration

hypoxia (environmental)

Dead zone (ecology)

particle (ecology)

ship pollution

water pollution

water quality

Silt Density Index

Salinity gradient

DWEER

Reverse osmosis plant

Notes

^ a b [Crittenden, John; Trussell, Rhodes; Hand, David; Howe, Kerry and Tchobanoglous, George. Water Treatment Principles and Design, Edition 2. John Wiley and Sons. New Jersey. 2005.]

^ Water Technology - Shuaiba Desalination Plant

^ Israel is No. 5 on Top 10 Cleantech List in Israel 21c A Focus Beyond Retrieved 2009-12-21

^ Desalination Plant Seawater Reverse Osmosis (SWRO) Plant

^ Ashkelon desalination plant A successful challenge

^ Treatment Systems for Household Water Supplies

References

Kramer, Matt. Making Sense of Wine. Philadelphia: Running Press, 2003.

External links

First Demonstration Of Reverse Osmosis

Sidney Loeb - Co-Inventor of Practical Reverse Osmosis

Membrane Animation and Filtration Comparison

Categories: Water treatment | Filters | Water technologyHidden categories: Articles needing additional references from June 2009 | All articles needing additional references | Wikipedia pages move-protected due to vandalism | All articles with unsourced statements | Articles with unsourced statements from April 2007
About the Author

I am China Hardware Suppliers writer, reports some information about anhydrous calcium aspartate , activated carbon msds.

GPH $12.99 GPH

Taam ATA00288 Rio Mini 90 Internal Power Filter 85 Gph $33.51 Rio mini 90 internal power filter. 85 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Taam ATA00289 Rio Mini 180 Internal Power Filter 120 Gph $33.77 Rio mini 180 internal power filter. 120 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Taam ATA00194 Rio 2100 Internal Power Filter 690 Gph $84.5 Rio 2100 internal power filter. 690 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Taam ATA00193 Rio 1700 Internal Power Filter 640 Gph $71.22 Rio 1700 internal power filter. 640 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Taam ATA00192 Rio 600 Internal Power Filter 200 Gph $48.05 Rio 600 internal power filter. 200 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Taam ATA00191 Rio 400 Internal Power Filter 190 Gph $45.05 Rio 400 internal power filter. 190 gph. Aquarium supplies. Submersible filters. Satisfaction ensured.

Shopzeus USA zeusd1EPST1253908 Pondmaster 190 Power Filter $182.02 PMK190 190 GPH PUMP FILTER

Pump: Mag Drive 700 Gph: A $104.13 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Danner PMK1700 PM1000 Filter with 700 GPH Pump $243.31 This supreme Pondmaster filter with 700 GPH pump set includes the Pondmaster 1000 filter and a Supreme Mag-Drive pump. The system comes complete with the filter, bell style and adjustable fountain heads, pump and a length of tubing to connect pump and filter. Filtering media provides effective biological and mechanical filtration. The system can be used as the sole source of bio-mechanical filtration or in conjunction with an additional external biological filter system. Materials: Plastic, metal UL and ULC-approved Capacity: 700 GPH (ponds up to 1,400 gallons) Fountain heads: Bell style and adjustable style Diverters sold separately Pump driven Switch type: Dial Liners sold separately Dimensions: 18.3 inches long x 13.3 inches wide x 4 inches deep Weight: 7.25 pounds Assembly required

Pump: Mag Drive Pump 950 Gph Submersible: A $191.21 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Pump: Mag Drive Pump 1800 Gph Submersible: A $164.01 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Pump: Mag Drive Pump 1200 Gph Submersible: A $127.46 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Pump: Mag Drive Pump 2400 Gph Submersible: A $183.56 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Pump: Mag Drive 250 Gph Pump: A $101.96 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPAPF3500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Pump: Mag Drive Pump 550 Gph: A $96.01 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging CODE model Cord Length Waranty PMPAPA1000 80 gph Submersible Pump 10’ 1 Year PMPAPB1230 130 gph Submersible Pump 10’ 1 Year PMPAPC1550 210 gph Submersible Pump 16’ 1 Year PMPAPD2000 270 gph Submersible Pump 16’ 2 Year PMPAPE3200 350 gph Submersible Pump 16’ 2 Year PMPPRO500 550t gph Submersible Pump 16’ 2 Year PMPAPG950 950 gph Submersible Pump 25’ 3 Year PMPAPH1200 1200 GPH Submersible Pump 25’ 3 Year PMPAPI1800 1800 gph Submersible Pump 25’ 3 Year PMPAPJ2400 2400 gph Submersible Pump 25’ 3 Year

Fluval U1 Underwater Filter (65 gph) $44.99 Fluval "U1" underwater filter is ideal for use in all aquarium or reptile environments. Use the underwater filter as a primary filter in smaller aquariums or as a supplementary filter for larger aquariums. Also great for tanks with low water levels. Fluval U1 underwater filter offers a Flip-Top for quick and easy maintenance. Suitable for aquariums up to 15 US gal. (55 L).

Fluval 205 Canister Filter (180 gph) $175.49 The Fluval 205 External Canister Filter provides complete, multi-stage filtration for aquariums up to 200 Liters (40 U.S. gallons). The modular design allows for quick and easy maintenance while flexible filter media chambers permit maximum versatility for basic to custom filter media configurations. The Fluval 205 External Canister Filter incorporates twin foam pre-filters that efficiently trap waste and debris, increase flow and reduce maintenance. Fluval 05 external canister filters offer quick, trouble-free maintenance features. These include instant priming, lift- lock clamps that securely lock the cover in place and an Aqua-Stop feature that stops the water flow without the need to disconnect hoses. The ribbed, opaque hosing bends and turns easily without kinking and makes installation and removal easier while supporting better water flow. An instructional DVD is included to simplify installation of the unit. Backed by a 3-year guarantee.

Fluval 105 Canister Filter (125 gph) $155.99 The Fluval 105 External Canister Filter provides complete, multi-stage filtration for aquariums up to 100 Liters (25 U.S. gallons). The modular design allows for quick and easy maintenance while flexible filter media chambers permit maximum versatility for basic to custom filter media configurations. The Fluval 105 External Canister Filter incorporates twin foam pre-filters that efficiently trap waste and debris, increase flow and reduce maintenance. Fluval 05 external canister filters offer quick, trouble-free maintenance features. These include instant priming, lift- lock clamps that provide easy access to the unit and an Aqua-Stop feature that stops the water flow without the need to disconnect hoses. The ribbed, opaque hosing bends and turns easily without kinking and makes installation and removal easier while supporting better water flow. An instructional DVD is included to simplify installation of the unit. Backed by a 3-year guarantee.

Fluval 305 Canister Filter (260 gph) $233.99 The Fluval 305 External Canister Filter provides complete, multi-stage filtration for aquariums up to 300 Liters (70 U.S. gallons). The modular design allows for quick and easy maintenance while flexible filter media chambers permit maximum versatility for basic to custom filter media configurations. The Fluval 305 External Canister Filter incorporates twin foam pre-filters that efficiently trap waste and debris, increase flow and reduce maintenance. Fluval 05 external canister filters offer quick, trouble-free maintenance features. These include instant priming, lift- lock clamps that securely lock the cover in place and an Aqua-Stop feature that stops the water flow without the need to disconnect hoses. The ribbed, opaque hosing bends and turns easily without kinking and makes installation and removal easier while supporting better water flow. An instructional DVD is included to simplify installation of the unit. Backed by a 3-year guarantee.

Fluval 405 Canister Filter (340 gph) $324.99 The Fluval 405 External Canister Filter provides complete, multi-stage filtration for aquariums up to 400 Liters (100 U.S. gallons). The modular design allows for quick and easy maintenance while flexible filter media chambers permit maximum versatility for basic to custom filter media configurations. The Fluval 405 External Canister Filter incorporates twin foam pre-filters that efficiently trap waste and debris, increase flow and reduce maintenance. Fluval 05 external canister filters offer quick, trouble-free maintenance features. These include instant priming, lift- lock clamps that securely lock the cover in place and an Aqua-Stop feature that stops the water flow without the need to disconnect hoses. The ribbed, opaque hosing bends and turns easily without kinking and makes installation and removal easier while supporting better water flow. An instructional DVD is included to simplify installation of the unit. Backed by a 3-year guarantee.

Fluval U2 Underwater Filter (105 gph) $64.99 Fluval "U2" underwater filter with three stage filtration is ideal for use in fresh, marine or reptile environments. Stage 1 foam removes large particles. Stage 2 poly/carbon cartridge traps fine debris, improves water clarity and removes impurities. Stage 3 BIOMAX provides optimal biological filtration efficiency. Fluval U2 underwater filter offers a Flip-Top for quick and easy maintenance and an adjustable 3 way flow for output flexibilty . Suitable for aquariums from 12-30 US gal.

Ovation 1000 Submersible Power Jet Filter - 265 gph $34.99 Ovation 1000 Submersible Power Jet Filters have an innovative design that makes them ideal for odd shaped or shallow habitats like terrariums and other partial water set-ups. Ovation 1000 has a max flow rate of 265 GPH and is recommended for tanks up to 80 gallons. These filters can be operated in the vertical or horizontal position, providing excellent mechanical and biological filtration as well as aeration. Each model includes a spray bar for more enhanced aeration and the air flow can be adjusted with the adjustable air regulator. These amazing little filters feature smooth, ultra quiet operation and dual filter elements of sponge and carbon for efficient filtering ability.

Aquascape 99771 MicroSkim Pond Filter Pumps Up to 2 500 Gph $291.17 Skims surface of the pond. Provides filtration. Ideal for ponds up to 1000 gallons. Aquascape pond surface skimmers remove unwanted debris including protein film from the surface of the pond before it has time to sink reducing unnecessary maintenance. These filters feature large removable debris nets that allow for quick and easy maintenance. Features:. Size: 20 L x 17.5 W x 17.5 H. Capacity: ponds up to 100 sq. ft. and less than 1 000 gal. Opening: 6 . Flow Rate: up to 3 000 GPH. Weight: 15.9 lbs. Includes:. Lid. Large volume rigid debris basket. Filter brush cartridge. Corrosion resistant hardware. Filter mat.

Fluval FX5 Canister Filter (925 gph) $467.99 The Fluval FX5 is a large capacity, multi-stage external canister filter system. Fluval FX5's massive capacity and powerful integrated motor processes and recirculates 607 U.S. gallons (2,300 liters)of water every hour, enabling precise management of water conditions for aquariums as large as 400 U.S. gallons (1,500 liters). Fluval FX5 features include: - A self-priming instant-start system that eliminates the need for manual siphoning - Unique click-fit AquaStop Valves that regulate water flow, rotate at 55 degree angles and allow for fast set-up and leak- proof maintenance - An innovative multi-functional aquarium rim connector to easily secure hosing in place - A convenient clog-free strainer to prevent build-up of solids that could impede water flow - A purge valve that allows for partial discharge of debris without needing to move the unit - Multi-directional twin output nozzles tp create specific water flows Fluval FX5 Smart Pump Technology (patent pending) ensures quiet, efficient operation. This self-priming system provides plug-in-and-start convenience. Smart Pump Technology employs an electronic circuit board to continually monitor the pump. Impeller speed and force are constantly measured to ensure powerful output and energy efficiency. On a 24-hour cycle, the pump will pause and allow trapped air to escape, ensuring ultimate filtration efficiency at all times. The true power behind Fluval filtration technology lies in the lift- out stack of media baskets. These allow custom media configurations. The large capacity baskets hold a total of 5.9L of media and enable precise stacking of media to suit the desired objectives of any aquarium.

Pump: Mag Drive Pump 350 Gph Submersible: A $118.96 These high quality submersible pumps are imported for Botanicare and are ideal for most hydroponic and water gardening applications. Models range in output from 60 GPH to 2400 GPH. Pumps have either threaded outputs or come with barbed fittings, so they are easy to connect to standard size tubing. All pumps are U.L. approved and come with a manufacturer’s warranty. Oil free mag-drive pump Only one moving part - no motor seals to wear out or leak Submersible or Inline use Energy efficient Directional flow outlet can be used in any orientation Sponge pre-filter prevents pump from clogging

Service Kit for Ani Mate Pond Pump 2000 - 600 gph $37.99 Replacement parts service kit for Fish Mate pond 600 gph submersible pond pump/filter/fountain. Includes: impeller, impeller cover, magnetic rotor, one-way arm, rear bearing and mounting bush.

Pond Works Pump 170 Gph $89.99 In-Line Multi-Purpose Mag Drive Pump High Performance Pumps Mag-drive pumps are a very energy efficient type of pump, due to the motor design; which is commonly referred to as "hysteresis" or "synchronous". These pumps have corrosion resistant housings, making them excellent for water gardening applications. Accepts 3/4" ID Tubing; 1/2" MNPT Discharge Snap-On Inlet Screen with Filter Media Helps Prevent Debris from Clogging Volute can Rotate in 90 degree Increments Pump Features Pump Specifications Application: Mag-Drive Pump Cord Length: 15' Max Flow Rate: 665 G.P.H. Max Watts: 80 Max Pond Capacity: 1330 Gallons Warranty: 1 Year Max Head: 9' Color: Black Ships Quickly!

Pond Works Pump 300 Gph $119.99 In-Line Multi-Purpose Mag Drive Pump High Performance Pumps Mag-drive pumps are a very energy efficient type of pump, due to the motor design; which is commonly referred to as "hysteresis" or "synchronous". These pumps have corrosion resistant housings, making them excellent for water gardening applications. Accepts 3/4" ID Tubing; 1/2" MNPT Discharge Snap-On Inlet Screen with Filter Media Helps Prevent Debris from Clogging Volute can Rotate in 90 degree Increments Pump Features Pump Specifications Application: Mag-Drive Pump Cord Length: 15' Max Flow Rate: 665 G.P.H. Max Watts: 80 Max Pond Capacity: 1330 Gallons Warranty: 1 Year Max Head: 9' Color: Black Ships Quickly!

Shopzeus USA zeusd1EPST1253898 Pondmaster 1700 Power Filter 700gph $364.75 PMK1700 700 GPH PUMP PM1000

Shopzeus USA zeusd1EPST1253901 Pondmaster 1250 Power Filter 250gph $271.88 PMK1250 250 GPH PUMP PM1000

Shopzeus USA zeusd1EPST1253899 Pondmaster 1500 Power Filter 500gph $339.1 PMK1500 500 GPH PUMP PM1000

PowerSweep 212 (125 GPH) UL Listed $39.05 Size: 125 GPH Zoo Med's Power Sweep powerheads are the first and only rotating powerheads on the market. With a full 60 degree of rotation the Power Sweep replicates natural water currents without the expense of a wave maker. The Power Sweep is fully submersible and can be used alone or in conjunction with an under gravel filter system. They are also cUL listed.

PowerSweep 228 (270 GPH) UL Listed $61.31 Size: 270 GPH Zoo Med's Power Sweep powerheads are the first and only rotating powerheads on the market. With a full 60 degree of rotation the Power Sweep replicates natural water currents without the expense of a wave maker. The Power Sweep is fully submersible and can be used alone or in conjunction with an under gravel filter system. They are also cUL listed.

Quiet One Pond Pump 6000 - 1506 gph $199.99 The Quiet One pond pump is great for many pond applications like running a filter or fountain This pump can be submersed or run inline. It has a 1" MPT inlet and outlet, 20' power cord, uses 140 watts, 3.8 amps, max flow rate: 1506 gph, max head height: 12.2'. Size: 6" x 4 1/4" x 5 1/2" high. Click here for Quiet One flow charts direct from the manufacturer (PDF viewer required).

Pump: Via Aqua Pump 1300 - 370 Gph: A $36.98 370 GPH Submersible pump with a 3 prong heavy duty cord. Includes several different attachments. This pump is great for Hydroponics Systems or Aquariums. Dimension: 4 1/4'' x 2 1/4'' x 2 3/4'' You'll love the oil-free design and quiet operation of this submersible water pump. ViaAqua pumps are ideal for circulating water, powering a wet/dry filter or U/V sterilizer, running a small waterfall or simply filling and draining an aquarium or pond. Pump comes complete with gravel filter adapter, flow-control valve, suction cups and standard tubing adapters. Built-in strainer keeps debris from fouling the impeller. 3/4'' outlet.

Mag Drive Water Pump 1200 Gph: J $168.26 Ideal for all water gardens, ponds, and statuary. PondMaster Mag-Drive pumps consist of a power unit encased in waterproof epoxy which creates a magnetic field. This drives a powerful magnetic impeller, the only moving part, which makes it extremely energy efficient (over 50% savings compared to equivalent conventional pumps). These pumps are made of environmentally friendly plastic, are virtually maintenance free and fish safe! Pump operates equally well in fresh or salt water, submerged or in-line. The PondMaster Mag-Drive Pumps are specifically designed for the demands of a pond and designed to run continuously, without seals wearing out. These pumps are oil-free and highly energy efficient. All pumps have prefilters except the 5000 gph which has a clog-free filter screen. 10' cord length. 3 year warranty (excluding impeller). 1200 GPH Maximum Flow 3/4'' MNPT discharge and 3/4'' FNPT Intake. Max height 15' 10' grounded power cord Operates submerged or in-line Ceramic shaft Foam pre-filter included 120V with 10ft Long 3 prong grounded Cord suitable for Indoor or Outdoor use Can be operated submersible or in-line. Suitable for Fresh or Saltwater Very powerful. Consumes a maximum of 110 Watts. Pump Measurements:6.4''Lx4.5''Wx4.6''H 3 Year Limited Manufacturers Warranty

Tags: filter,, gph filter, gph filter aquarium, ground, pool, pools, pump

This entry was posted on Sunday, December 14th, 2008 at 4:22 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.